Step 4 - File Conflict Resolution

<< Click to Display Table of Contents >>

Navigation:  Peer Management Center Help > Creating a File Collaboration Job >

Step 4 - File Conflict Resolution

Previous pageReturn to chapter overviewNext page

 

File Conflict Resolution allows you to specify the type of file conflict resolution to use during the initial scan when a file conflict exists for a file between two or more hosts. Configuration is available by selecting Conflict Resolution from the tree node within the File Collaboration Configuration dialog.

 

 

Overview

 

Conflict resolution is a key feature of file collaboration that is in effect at the start of a session. When a file collaboration job begins, the host participants' configured folders are synchronized by a scan and merge phase, during which conflicts can be detected. Below, we will define file conflicts, describe our detection scheme, and the configuration options we provide to resolve them.

 

 

Defining a Conflict

 

When a session begins, the participants' folders are first scanned then merged to form a collective view of all participants' content. All files found under the designated folders are subject to collaboration, except for those excluded by filtration (see Global File Filter Configuration for more details).

 

A potential conflict occurs when a file path is found to exist on more than one host in a file collaboration job. For example, the following files are found to be in conflict:

 

\\Host-A\FC-Session-UserGuide\release-1.0\readme.txt

\\Host-B\FileCollab-UG\release-1.0\readme.txt

\\Host-C\FCS-UserGuide\release-1.0\readme.txt

 

In this example, the file '\release-1.0\readme.txt' is found to be in conflict across three hosts. Note that each host can designate varying root folders. Content below the Root Folder resides under a shared namespace. Conflicts may occur across a partial or total set of participant hosts.

 

A file conflict can occur for any of the following reasons:

 

Two users open a file at the same time, or in-and-around the same time.

A file is open at the start of a job and has been modified on a host where the configured conflict resolution strategy selects a different host as the winner.

Two or more users have the same file open on different hosts when a collaboration job is started.

A file was modified on two or more hosts between job restarts or network outages.

Peer Management Center is unable to obtain a lock on a target host file for various reasons.

Peer Management Center may conflict a file when an unexpected error occurs or a file is in an unexpected state.

 

Resolving a Conflict

 

The goal of conflict resolution is to designate one instance of a conflicted file as the "winning" copy or the one designated as the source for synchronization. The criteria for resolving conflicts are based on the file's metadata such as size, modification time or host name.

 

It is important to note that conflict resolution must select a single instance of a file, although it is quite possible that several copies of a file are potential candidates. Drawing from the examples listed in the previous section, if our session was configured to resolve conflicts based on a files last modified time and all instances of '\release-1.0\readme.txt' had the same size and last modified time, then all three would be resolution candidates. In this case, the winner would be arbitrarily selected from the candidate set. This concept applies to all resolution types that are prone to multiple candidate selection.

 

Once the merge and conflict resolution phases have completed for the session, synchronization transfers begin to distribute the source content. This includes all source copies of conflict winners as well as files that are missing from participants.

 

See the File Conflict View for a more detailed explanation on how the file conflict process works and how to remove file conflicts and quarantines.

 

 

Configuration

 

The following is a view of the Conflict Resolution configuration page.

 

jobconfig_conflict_resolution_37

 

The conflict resolution types that are currently available are listed as follows:

 

 

All the types listed above have the potential for producing multiple resolution candidates. A collaboration session can be configured with any one of the available conflict resolvers. If a resolver produces more than one candidate for a conflicted file, a winner will be selected arbitrarily.

 

Advanced Conflict Resolution options are list as follows:

 

 

Once all File Conflict Resolvers are selected and set to your liking, you can either save the configuration and exit the dialog, or you can continue with the configuration process by going to Step 5 - Delta Replication.